This is a simple, almost any paper can be recycled.
The most recommended roles are:
* Continuous Forms (Highly suitable as they are resistant because they contain long fibers).
* Butcher paper that is used to wrap (unless it contains a lot of wood fibers),
* paper bags and envelopes.
* The paper already printed (but you should not use any that is in excess).
* The newspaper can be used to give volume, when combined with other materials.
Avoid glossy papers and glossy, it will probably be coated with kaolin, which may cause dusty patches on the paper.
Variations:
* Rags * Cotton Fibers Plant
Materials: blender
* A * Molds * Newspapers complementary
Spatula
* Manufacture of pulp
First remove any residual glue, metal hooks or anything that may damage the final product or damage the cookware work. Then tear the paper into pieces of about 3 cm2 and soak in water overnight (If A long soak will remove the paper, but do not let more than a week because it will become smelly.) The time can be trimmed if boiling water is poured on paper and left a couple of hours, or it can be boiled in a steel container Large size for half an hour. After blending the wet paper gradually. Start with 10 to 15 pieces for every ¾ of a liter, then you can judge how much paper can be liquefied easily at each round (Do not force the blender, and that may be damaged and the paper will not drop uniformly). Blend until smooth paper are suspended in the pulp, and has a smooth, creamy consistency (blending should be avoided for a long time, since c will be shorter and less resistant fibers will be the paper.)
Storage
remaining pulp pulp can be saved, but if stored for a long time to release bad start smell, so it should be washed thoroughly before use, if this is very hard to take a little bleach (bleach), is left about an hour and then rinsed. To prevent rot can add a few drops of formaldehyde (or formaldehyde) per liter of water. Training
leaves Fill the tub with the pulp, so that the mold and how to dive with ease, but not less than 7 or 8 cm below the edge because otherwise it will splash the workspace when to dry the mold and form. Then stir the pulp with your hand or shake it with a brush. Do this procedure quickly, before the pulp settle to the bottom of the tub. Immediately place formed over the mold, the side of the screen. Hold them firmly and vertically dipping toward the opposite side of the tub. As slight movements, tilting the pan until it is flat and draw it to the front of the tub to be completely submerged. Pull up to collect the pulp. Holding the mold in a horizontal position, it gives a quick jolt from side to side and front to back. You have to make this move before all the water has drained and the flesh has started to harden. This action will match the pulp and disperse the fibers preventing all are arranged in the same direction. To end hold the top mold and shape the tub slightly tilted to drain excess water. Drying
Leave pan on a stack of newspapers will absorb moisture from the mold, so it will be replaced. When you have drained most of the water from the mold and the sheet of paper, it is more likely to tilt. They lean against a wall or furniture to dry up, but be careful that the flesh is dry enough, otherwise it could slip. When the paper is completely dry, carefully stick a knife edge to separate the role of the mold and carefully peel the leaf of the mesh.
The most recommended roles are:
* Continuous Forms (Highly suitable as they are resistant because they contain long fibers).
* Butcher paper that is used to wrap (unless it contains a lot of wood fibers),
* paper bags and envelopes.
* The paper already printed (but you should not use any that is in excess).
* The newspaper can be used to give volume, when combined with other materials.
Avoid glossy papers and glossy, it will probably be coated with kaolin, which may cause dusty patches on the paper.
Variations:
* Rags * Cotton Fibers Plant
Materials: blender
* A * Molds * Newspapers complementary
Spatula
* Manufacture of pulp
First remove any residual glue, metal hooks or anything that may damage the final product or damage the cookware work. Then tear the paper into pieces of about 3 cm2 and soak in water overnight (If A long soak will remove the paper, but do not let more than a week because it will become smelly.) The time can be trimmed if boiling water is poured on paper and left a couple of hours, or it can be boiled in a steel container Large size for half an hour. After blending the wet paper gradually. Start with 10 to 15 pieces for every ¾ of a liter, then you can judge how much paper can be liquefied easily at each round (Do not force the blender, and that may be damaged and the paper will not drop uniformly). Blend until smooth paper are suspended in the pulp, and has a smooth, creamy consistency (blending should be avoided for a long time, since c will be shorter and less resistant fibers will be the paper.)
Storage
remaining pulp pulp can be saved, but if stored for a long time to release bad start smell, so it should be washed thoroughly before use, if this is very hard to take a little bleach (bleach), is left about an hour and then rinsed. To prevent rot can add a few drops of formaldehyde (or formaldehyde) per liter of water. Training
leaves Fill the tub with the pulp, so that the mold and how to dive with ease, but not less than 7 or 8 cm below the edge because otherwise it will splash the workspace when to dry the mold and form. Then stir the pulp with your hand or shake it with a brush. Do this procedure quickly, before the pulp settle to the bottom of the tub. Immediately place formed over the mold, the side of the screen. Hold them firmly and vertically dipping toward the opposite side of the tub. As slight movements, tilting the pan until it is flat and draw it to the front of the tub to be completely submerged. Pull up to collect the pulp. Holding the mold in a horizontal position, it gives a quick jolt from side to side and front to back. You have to make this move before all the water has drained and the flesh has started to harden. This action will match the pulp and disperse the fibers preventing all are arranged in the same direction. To end hold the top mold and shape the tub slightly tilted to drain excess water. Drying
Leave pan on a stack of newspapers will absorb moisture from the mold, so it will be replaced. When you have drained most of the water from the mold and the sheet of paper, it is more likely to tilt. They lean against a wall or furniture to dry up, but be careful that the flesh is dry enough, otherwise it could slip. When the paper is completely dry, carefully stick a knife edge to separate the role of the mold and carefully peel the leaf of the mesh.
